3-AXIS CNC STEPPER MOTOR COMPLETE KIT
 

TOP QUALITY 3 AXIS CNC STEPPER MOTOR COMPLETE KIT, THE SYSTEM INCLUDES DRIVER BOARD, TWIN RELAY BOARD, POWER SUPPLY AND DB25 PARALLEL CABLE, THIS IS IDEAL FOR YOUR PERSONAL OR HOBBY CNC MACHINE. WIRE THEM, PLUG IN TO YOUR PC PARALLEL PORT AND PLUG IN A POWER SUPPLY

THE KIT INCLUDE

<<<  3 USED NEMA 23 STEPPER MOTORS, MINEBA TYPE LM-C355  >>>

FEATURES

• 5.1V @ 1.6A per phase

• 90oz/in torque

• 1.8 degree step (200 steps per revolution) in full mode

• 0.9 degree step (400 steps per revolution) in half mode

• The driver board can manage this motor to 0.225 degree step (1600 steps per revolution) in 1/8 micro step mode

• 6 leads configurable as unipolar or bipolar

• 1/4 inch diameter x 3/4 inch large shaft

<<<  1 NEW MECHATRONICS 3-AXIS STEPPER MOTOR DRIVER  >>>

FEATURES

• Made with Top Surface Mount Technology

• Two phase bipolar (PWM Technology) this board doesn't need any external resistor for current motor adjustment.

• Resolution (Full step, 1/2 step, 1/4 step, 1/8 step) selectable via dip switch for each axis, also, you can get a resolution of 1600 steps per 360º revolution with a conventional 200 steps motor, ¡Imagine the fine movement that you will get!

• All integrated circuits drivers and optocouplers are mounted in sockets. If you are not an electronics expert, don't worry if you has fired the driver for any reason, for less than USD$10 and practically no tools and no solder tool is needed, you can repair it in less than 5 minutes. No other driver board in the market offer this to you. With this board just buy once, in case of damage is no need to buy it again. Nobody has this feature, don't waste money and time.

• 2.5A motor current capacity per phase, in every axis

• Individual axis enable/disable, via optocoupler input terminal (can be used as limit switch)

• Full Adjustable stepper motor current via potentiometer on board

• DB25 MALE connector on board for PC parallel port

• All inputs signals are optocoupled for PC parallel port protection

• Full access to all unused DB25 pins connector via terminal block, easy connection for prototyping work

• 24VDC @ 2-to-6 amp power supply required, 12VDC as minimum, 32VCD as maximum

• Individual heat sink per axis

• 4 Wire, 6 Wire and 8 Wire (NEMA 17, NEMA 23, NEMA 34) Bipolar or Unipolar stepper motors can be used with 3 axis drive

• Fuse integrated for electrical protection

Optocoupler protect your PC parallel port isolating of the board.

This new model is made using Surface Mount Technology, it reduces the PCB size, is better for your applications.

Individual heat sink per axis.

Every IC driver and optocoupler are mounted in socket, you can replace them if they're damaged in just 5 minutes!.

The motor current is adjusted with the  potentiometers on board.

You can configurate the stepper resolution with the Dip Switch on board, also, the configuration table is printed on board.

Fuse integrated per axis, as electrical protection. This fuse protect the printed circuit board tracks in case of short circuit.

Power LED on board per axis.

DB25 MALE connector, ideal for your PC parallel port.

Limit switch per axis and breakout for unused DB25 pins, ideal for prototyping work.

<<<  1 NEW HP POWER SUPPLY  >>>

FEATURES

• 220 or 120 Voltage input

• 31VDC @ 2.4A output

• U.S. style 3-prong plug power cable included

<<<  1 NEW TWIN CNC RELAY BOARD  >>>

FEATURES

• Two relays on board

• It can activate/deactivate tools that work at 120VAC or 220VAC as a Motor Tool, Router, Coolant Pumps, etc.

• Slave and single mode configuration, selectable on board; for single mode jump pins 2-3 in this mode you can control two different circuits with a control signal each; for slave mode jumps pins 1-2 in this mode you can control two circuits with a single control signal

• All inputs signals are optocoupled for computer parallel port protection

• If you are not an electronics expert, just follow the instructions in the datasheet. It can not damage your computer because it has optocoupled inputs. Nobody has this feature, don't waste money and time

• Every relay can close electrical circuits at 125VAC@15A or 250VAC@10A as maximum

• The output terminals are large for an easy connection to your power circuits

• 12VDC to 35VDC @ 100mA power supply required, 12VDC as minimum, 35VCD as maximum; you can use the same power supply of your stepper motor driver board

• Compatible with all our stepper motor driver boards

<<<  1 NEW 8ft DB25 STRAIGHT THROUGH CABLE  >>>

THE DRIVER BOARD AND THE TWIN RELAY BOARD HAS A COMPLETE MANUAL WITH EASY INSTRUCTIONS AND WIRING DIAGRAM, DOWNLOAD HERE

YOU NEED ADOBE READER TO SEE IT  

I TESTED THIS DRIVER BOARD USING KCAM SOFTWARE VER. 4.0 www.kellyware.com/kcam

KCam 4 Router/Mill software is designed to run low cost hobby CNC equipment. Program your paths using the built in G-code editor or import DXF, NC and PLT files. Create signs and plates using your CAD software and import your work into KCam

YOU CAN DOWNLOAD FULL OPERATE DEMO VERSION AND RUN THE STEPPER SYSTEM

YES!, THE RELAY BOARD WORKS WITH MACH2, MACH3 AND ANY SOFTWARE THAT SENDS CONTROL SIGNALS THROUGH PARALLEL PORT!

YOU CAN DOWNLOAD OPERATE DEMO VERSION

www.machsupport.com

YOU CAN SEE THE 3 AXIS SYSTEM WORKING VIDEO HERE !

http://video.google.es/videoplay?docid=-5281796970250102073&q=3axisdrive